Funklösungen Infinet

CENI-GWEXERinfiNET EX® Network and ER Wireless Gateway – International VersionProvides a wireless gateway for infiNET EX® and ER "Extended Range" devices.The CEN-GWEXER is a 2-way RF wireless transceiver designed for use with Crestron® infiNET EX® and “ER” (Extended Range RF) wireless devices. A single CEN-GWEXER gateway enables an entire wireless network of Crestron remotes, keypads, lighting dimmers, motorized shades, thermostats, door locks, and other devices to communicate with a Crestron control system.infiNET EX® TechnologyUltra-reliable infiNET EX wireless technology provides steadfast 2-way RF communications throughout a residential or commercial structure without the need for physical control wiring. Employing a 2.4 GHz mesh network topology, nearly every infiNET EX device on the network acts as an “expander,” relaying wireless commands between the gateway and all the other “EX” devices on the network to ensure that every command reaches its intended destination without disruption. Each infiNET EX device that is added to the network effectively increases the range and stability of the entire network by providing multiple redundant signal paths. The wireless range between any two EX devices is typically up to 150 ft (46 m) indoors.[1]“ER” Extended Range RF TechnologyCrestron Extended Range (ER) wireless technology enables compatibility with certain Crestron wireless touch screens and handheld remotes including the TSR-302, TST-600, TST-602, and TST-902.[2] Crestron “ER” operates in the same 2.4 GHZ spectrum as infiNET EX, and is specifically optimized for use with wireless touch screen devices to ensure robust and dependable bidirectional RF communications. The CEN-GWEXER continuously monitors each ER device on the network, diligently keeping track when a device goes to sleep, shuts down, or wanders out of range, and restores communications seamlessly when the device reappears on the network. The typical wireless range for ER devices is 100 to 200 feet indoors, or up to 1000 feet outdoors. For even greater coverage, ER supports roaming amongst up to eight gateways.[3]Easy SetupThe CEN-GWEXER can manage both infiNET EX and ER wireless devices simultaneously, eliminating the need for separate gateways, antennas, and LAN connections. Setting up a network of infiNET EX and/or ER devices is simple, utilizing dynamic discovery to locate and acquire each wireless device automatically. If no ER devices are acquired, the CEN-GWEXER can support up to 100 infiNET EX devices (inclusive of up to six Crestron MLX-3 handheld remotes [2]). Each ER device that is added to the network negates ten EX devices, with a maximum of ten ER devices allowed. For a more detailed breakdown, please refer to “Supported Devices” in the specifications section of this spec sheet.[4]Single-Wire HookupThe CEN-GWEXER gateway communicates with a control system over Ethernet and gets its operating power over the same Ethernet connection using PoE technology. PoE (Power over Ethernet) simply requires the presence of an 802.3af or 802.3at PoE power source.Crestron offers the PWE-4803RU PoE Injector, which connects inline with the Ethernet cable, allowing for installation at any convenient location between the gateway and the network switch. The PWE-4803RU is capable of powering a single gateway, and is available separately or packaged with the gateway as model CEN-GWEXER-PWE or CENI-GWEXER-PWE.Crestron also offers Ethernet switches with built-in PoE (models CEN-SW-POE-5 and CEN-SWPOE-16 [5]), affording a complete high-performance networking solution capable of providing PoE for multiple gateways and other PoE devices. Using an Ethernet switch with built-in PoE eliminates the need for individual PoE Injectors.As an alternative to PoE, the CEN-GWEXER can be powered using an optional 24VDC power pack, model PW-2407WU.[5]Integrator Friendly EnclosureThe CEN-GWEXER features the Crestron IFE form factor, a compact “Integrator Friendly Enclosure” design that fits almost anywhere and enables a variety of installation options. Its shape allows multiple gateways and other IFE compliant devices to be stacked together. Using the included mounting bracket, it can be fastened to any flat surface or snapped onto a standard DIN rail. Rack mount and pole mount kits are also available.[5] Key FeaturesMultipurpose 2-way RF wireless gatewaySimultaneously supports infiNET EX® and Crestron “ER” wireless devices [2]Ultra dependable infiNET EX mesh network technology“Extended Range” RF technology optimized for wireless touch screen remotesDynamic discovery for fast, easy setup"Wi-Fi® friendly" channel selection for trouble-free operationBuilt-in RF network diagnosticsUp to 150 feet (46 meters) infiNET EX range indoors, 250 feet (76 m) outdoors [1]100 to 200 feet (33 to 66 meters) ER range indoors, 1000 feet outdoorsSupports infiNET EX expanders and ER roaming for extended coverage [1,3]Extendable antenna using optional ANT-EXT [5]Compact, stackable “IFE small” form factorSurface or DIN rail mountable using bracket providedAvailable rack mount and pole mount options [5]High-speed Ethernet control system interface24VDC or PoE network poweredModels available with PoE injector includedOptional 24VDC power pack sold separately

The Crestron® CLC-1LEDPWM-RGBW-EX provides four independently controlled channels of RGBW color mixing for LEDs.  Achieve spectacular colored accent lighting to highlight architectural features, provide mood lighting, or spread a little holiday cheer.  Choose from an array of white hues on any or all of the four channels to boost the general room illumination.  This RGBW LED Controller uses a configurable Pulse Width Modulation (PWM) frequency for flicker-free performance. Over-current protection ensures the long life of this LED controller.infiNET EX®Ultra-reliable infiNET EX wireless technology provides steadfast two-way RF communications throughout a residential or commercial structure without the need for physical control wiring. Employing a 2.4 GHz mesh network topology, each infiNET EX device functions as an expander, passing command signals through to every other infiNET EX device within range (approximately 150 feet or 46 meters indoors), ensuring that every command reaches its intended destination without disruption.[1]The CLC-1LEDPWM-RGBW-EX communicates with a Crestron control system via an infiNET EX Wireless Gateway (model CEN-GWEXER, DIN-AP3MEX, or MC3[2]). Up to 100 infiNET EX devices may coexist on a single wireless network, and every device that is added to the network effectively increases the range and stability of the entire network by providing multiple redundant signal paths.[1] Built-in Dynamic Frequency Allocation continuously monitors RF conditions, automatically selecting the clearest channel to prevent interference from neighboring networks, cordless phones, and microwaves. Key Features4 independently-controlled channels of RGBW color mixing for LEDsMultiple white hues on any or all four channelsConfigurable PWM for flicker-free performanceOver-current protectioninfiNET EX® wireless communications

CLCI-1DIMFLV2EX-WWireless In-Ceiling 0-10V Dimmer, 230VACOffers two channels of 0-10 Volt dimming control. Wireless infiNET EX® technology connects the easy-to-install CLCI-1DIMFLV2EX-W to a Crestron® control system for complete lighting control.The CLCI-1DIMFLV2EX-W is a two-channel 0-10 Volt dimmer capable of controlling two independent, 230 Volt AC lighting loads. Its ultra-slim design allows it to be installed in the ceiling, either on or near the lighting fixture. Powered by infiNET EX® technology, the CLCI device communicates wirelessly with the Crestron® control system, making it perfect for both new and retrofit applications. Additionally, the dimmer installs inline without requiring any special wiring and can be controlled via a standard light switch.Easy Loop-Thru WiringFeeding each dimmer is a set of terminals used to power the unit. A second set of high-voltage terminals wired in parallel allow for a fast, clean installation when deploying multiple CLCI units. No need for wire connectors or extra gang boxes; just "daisy chain" multiple CLCIs together. In certain retrofit applications, this lets you create more zones from what was originally wired.Out-of-the-box Control via Standard SwitchThe CLCI-1DIMFLV2EX-W uses either a momentary or a maintained switch to provide a closure, such as a standard lighting switch. A standard lighting switch, the kind carried in any hardware store, is a cost-effective solution for basic on and off functions. A momentary, pushbutton-type switch can be used when the application requires dimming the load. The momentary switch can be set up so that tapping the button turns the connected load on and off, while pressing and holding the button dims the load up or down.Complete Crestron ControlBecause it's connected to the Crestron system, the CLCI-1DIMFLV2EX-W can also be controlled from any keypad, touch panel, remote, or mobile device. Tie in occupancy sensors and photocells together with Crestron Fusion RV® software for a complete solution to effectively manage room assets.Simple SetupSetup is simple, especially when using a connected maintained or momentary switch. A specific series of button presses initiates the wireless device's acquire mode, so there's no need to climb a ladder to join the device to the infiNET EX network.infiNET EXUltra-reliable infiNET EX wireless technology provides steadfast two-way RF communications throughout a residential or commercial structure without the need for physical control wiring. Employing a 2.4 GHz mesh network topology, each infiNET EX device functions as an expander, passing command signals through to every other infiNET EX device within range (approximately 150 feet or 46 meters indoors), ensuring that every command reaches its intended destination without disruption.[1]The CLCI-1DIMFLV2EX-W communicates with a Crestron® control system via an infiNET EX Wireless Gateway (model CEN-RFGW-EX, DIN-AP3MEX, or MC3[2]). Up to 100 infiNET EX devices may coexist on a single wireless network, and every device that is added to the network effectively increases the range and stability of the entire network by providing multiple redundant signal paths.[1] Built-in Dynamic Frequency Allocation continuously monitors RF conditions, automatically selecting the clearest channel to prevent interference from neighboring networks, cordless phones, and microwaves. Key FeaturesCompact 2-channel 0-10 Volt dimmer for new or retrofit applicationsTwo independently-controlled zone outputsCrestron® control of any lighting fixtureNo special wiring—installs inline at the fixtureMaximum 500 VA load capacity per channelReliable wireless communication using infiNET EX® technologyLocal controls for testing and maintenanceBuilt-in support for control via standard momentary or maintained switchSetup via on-board button or connected switchDaisy-chain units for easy deploymentOperates across voltage range of 220-240 VAC

The CLCI‑1SW2EX‑W is a two-channel switch capable of controlling two independent, 230VAC lighting loads. Its ultra-slim design allows it to be installed in the ceiling, either next to or near the fixture. The CLCI‑1SW2EX‑W communicates with the Crestron control system using infiNET EX® wireless technology, making it perfect for both new and retrofit applications.The CLCI‑1SW2EX‑W installs inline without requiring special wiring and can be controlled via a standard light switch.Two-Channel SwitchingThe CLCI‑1SW2EX‑W switches incandescent, tungsten-halogen, magnetic low-voltage, electronic low-voltage, fluorescent ballast, neon/cold cathode, and motor loads for each of the two independent channels. Two sets of screw terminals (internally wired in parallel) enable easy wiring to each load of up to 500 VA.Easy Loop-Thru WiringThe CLCI‑1SW2EX‑W is powered using a set of high-voltage screw terminals and has a second set of terminals that are wired in parallel to easily daisy-chain additional CLCI-series devices. This provides a fast, clean installation when deploying multiple CLCI- devices and eliminates the need for additional wire connectors or extra gang boxes. In some retrofit applications, this lets you create more zones from what was originally wired.Out-of-the-Box Control via Standard SwitchThe CLCI‑1SW2EX‑W provides built-in support for applications that require basic load control using a cost effective maintained or momentary switch to control the load. Use a maintained or momentary switch to perform basic on and off control.Complete Crestron ControlA Crestron control system connection allows the CLCI‑1SW2EX‑W to be controlled from any keypad, touch panel, remote, or mobile device. Tie in occupancy sensors and photocells together with Crestron Fusion® software for a complete solution to effectively manage energy.Simple SetupSetup is simple, especially when using a connected maintained or momentary switch. A specific series of button presses initiates the wireless device acquire mode, so there's no need to climb a ladder to join the device to the infiNET EX network.infiNET EX® Wireless CommunicationsinfiNET EX wireless technology provides two way RF communications throughout a residential or commercial structure without the need for physical control wiring. Each infiNET EX device acts as an expander by sending command signals to other infiNET EX devices in range (approximately 150 ft (46 m) indoors) to ensure reliability and stability.The device communicates with a control system via a Crestron Wireless Gateway (sold separately). Up to 100 infiNET EX devices may coexist on a wireless network.Note: Any infiNET EX device that provides expander functionality will effectively extend the range of the wireless network beyond the initial range of the gateway. Battery-powered infiNET EX devices do not provide expander functionality. A dedicated infiNET EX Wireless Expander is also available (CLW-EXPEX, sold separately). Key Features2-channel switch for 230VAC lighting loadsProvides control of lighting fixturesCompact surface-mount design for new or retrofit applicationsTwo independently-controlled zone outputsNo special wiring—installs inline at the deviceRated 500 VA load capacity per channelinfiNET EX® wireless communication ensures reliable operationLocal controls for setupBuilt-in support for control via standard momentary or maintained switchSetup via on-board button or connected switchDaisy-chain units for easy deploymentOperates using 220-240VAC powerCaptive screw terminal connections

The CLCI-DIMUEX-W is a universal dimmer capable of dimming 230VAC lighting loads. Its ultra-slim design allows it to be installed in the ceiling, next to or near the fixture. The CLCI‑DIMUEX‑W communicates with the Crestron control system using infiNET EX® wireless technology, making it perfect for both new and retrofit applications.The CLCI‑DIMUEX‑W installs inline without requiring special wiring and can be controlled via a standard light switch.Universal DimmingThe CLCI‑DIMUEX‑W supports dimming incandescent, tungsten-halogen, magnetic low voltage, electronic low voltage and dimmable CFL loads. Load detection circuitry automatically determines forward- or reverse-phase dimming mode. Two sets of screw terminals (internally wired in parallel) enable easy wiring to more than one load of up to 300 W/VA.Easy Loop-Thru WiringThe CLCI‑DIMUEX‑W is powered using a set of high-voltage screw terminals and has a second set of terminals that are wired in parallel to easily daisy-chain additional CLCI-series devices. This provides a fast, clean installation when deploying multiple CLCI- devices and eliminates the need for additional wire connectors or extra gang boxes. In some retrofit applications, this lets you create more zones from what was originally wired.Out-of-the-box Control via Standard SwitchThe CLCI‑DIMUEX‑W provides built-in support for applications that require basic load control using a cost effective maintained or momentary switch to control the load. Use a maintained or momentary switch to perform basic on and off control. A momentary switch can also be used for basic dimming control by pressing and holding the button.Complete Crestron ControlA Crestron control system connection allows the CLCI‑DIMUEX‑W to be controlled from any keypad, touch panel, remote, or mobile device. Tie in occupancy sensors and photocells together with Crestron Fusion® software for a complete solution to effectively manage energy.Simple SetupSetup is simple, especially when using a connected maintained or momentary switch. A specific series of button presses initiates the wireless device acquire mode, so there's no need to climb a ladder to join the device to the infiNET EX network.infiNET EX™ CommunicationsinfiNET EX wireless technology provides two way RF communications throughout a residential or commercial structure without the need for physical control wiring. Each infiNET EX device acts as an expander by sending command signals to other infiNET EX devices in range (approximately 150 ft (46 m) indoors) to ensure reliability and stability.The device communicates with a control system via a Crestron Wireless Gateway (sold separately). Up to 100 infiNET EX devices may coexist on a wireless network.Note: Any infiNET EX device that provides expander functionality will effectively extend the range of the wireless network beyond the initial range of the gateway. Battery-powered infiNET EX devices do not provide expander functionality. A dedicated infiNET EX Wireless Expander is also available (CLW-EXPEX, sold separately). Key Features1-channel universal dimmerProvides control of lighting fixturesCompact surface-mount design for new or retrofit applicationsNo special wiring—installs inline at the deviceRated 300 W/VA load capacityinfiNET EX® wireless communication ensures reliable operationLocal controls for setupBuilt-in support for control via standard momentary or maintained switchSetup via on-board button or connected switchDaisy-chain units for easy deploymentOperates using 220-240VAC powerCaptive screw terminal connections

The CLWI-1SW2EX delivers native Crestron® control to up to two individual lights or other switched loads, in new or retrofit 230 Volt applications. Featuring reliable infiNET EX® wireless technology, the CLWI-1SW2EX can be installed in virtually any location thanks to reliable mesh networking. Dual-load control on the CLWI-1SW2EX is perfect for controlling a bathroom light and exhaust fan in a single gang.Field-Replaceable and Engravable ButtonsThe CLWI-1SW2EX features engravable buttons that can be swapped out in the field. Change of room décor or functionality is easy to handle long after the dimmer or switch has been installed. Positive snap-on fittings require no tools. Configure the dimmer or switch with a large rocker, or any combination of up to two adjacent half-size rockers or triple button pad. Each CLWI-1SW2EX ships with a full assortment of blank buttons as well.Integrated KeypadBecause the CLWI-1SW2EX is attached to the Crestron network, it can also function as a keypad, sending commands to trigger whole-room lighting scenes or distributed audio functions. Supporting up to six buttons, the in-wall dimmer or switch serves as a great user control interface in any Crestron system. Its single-box form factor maximizes control capability in a small space while increasing the opportunity for Crestron control in every room. Also available are aesthetically matched standalone keypads which use Cresnet® or infiNET EX® communications.infiNET EXUltra-reliable infiNET EX wireless technology provides steadfast two-way RF communications throughout a residential or commercial structure without the need for physical control wiring. Employing a 2.4 GHz mesh network topology, each infiNET EX device functions as an expander, passing command signals through to every other infiNET EX device within range (approximately 150 feet or 46 meters indoors), ensuring that every command reaches its intended destination without disruption.[1]The CLWI-1SW2EX communicates with a Crestron control system via an infiNET EX Wireless Gateway (model CEN-GWEXER, DIN-AP3MEX, or MC3[2]). Up to 100 infiNET EX devices may coexist on a single wireless network, and every non-battery-powered device that is added to the network effectively increases the range and stability of the entire network by providing multiple redundant signal paths[1]. Built-in Dynamic Frequency Allocation continuously monitors RF conditions, automatically selecting the clearest channel to prevent interference from neighboring networks, cordless phones, and microwaves.Streamlined InstallationIn addition to field replaceable buttons, the CLWI-1SW2EX features screw-clamp connectors for simplified wiring while reducing installation time and material costs. So slim, the CLWI-1SW2EX can be installed in square gang boxes making them the perfect choice for both new and retrofit projects. Key FeaturesControl two individual loads from a single gangField-replaceable and engravable buttonsAvailable in anthracite or white finishesinfiNET EX® robust communicationConfigurable up to six buttonsScrew-clamp connectors for easy installationStylish bargraph LED array provides real-time status feedback