C2N-UNI8IO

The Crestron CGEIB-IP is a control interface by which a Crestron control systemcan be coupled to a KNX (previously known as EIB) installation using either RS232or Ethernet (TCP/IP). Also, the Crestron CGEIB-IP filters the desired informationout of received KNX/EIB messages and sends them to the Crestron control systemvia the same interface (RS232 or TCP/IP), which provides the Crestron installationwith live updates of the KNX/EIB installation.Crestron always provided a valuable solution to interoperate with a KNX/EIBnetwork by means of the CGEIB: a DIN-rail mountable EIB node that could becontrolled only over RS-232. Crestron has expanded their CGEIB with thepossibility to be controlled over TCP-IP. This CGEIB-IP is a new unit that replacesthe CGEIB, but as it still holds an RS-232 port as well, it is perfectly backwardscompatible. So, for replacing the CGEIB in an existing installation, one can installthis CGEIB-IP.

The DIN-2MC2 is a 2-channel motor control module designed to provide control of bidirectional motors for drapes, shades, projection screens, lifts, skylights, and gates. Each channel supports up/down or open/close control of a conventional three-wire bidirectional type motor up to 1/2 HP at voltages up to 240 Volts. Built-in timing and interlock logic make it easy to program the DIN-2MC2 for failsafe operation.Override InputAn override input is provided to allow an external contact closure to momentarily override the control system program and set each channel output to its override preset state. States can be set and saved locally from the front panel, or remotely via software.DIN Rail InstallationThe DIN-2MC2 is designed to snap onto a standard DIN rail for installation in a wall mount enclosure. Wiring connections are made using screw terminals positioned along the top and bottom, clearly accessible from the front for easy installation and servicing. All setup controls and indicators are positioned on the center front panel. When installed in an enclosure utilizing 45 mm cutouts, the DIN-2MC2's front panel stays accessible while the connections are concealed.Cresnet®The DIN-2MC2 communicates with a Crestron control system via the Cresnet control network. A pair of Cresnet ports is provided on the DIN-2MC2 allowing for easy daisy-chaining of several DIN Rail Series automation control modules. Key FeaturesDual-channel bidirectional motor controlSupports 120 to 240 Volt 50/60 HzOverride inputCresnet® communicationsSetup via front panel or softwareProgrammable functionality via DIN-AP26M wide DIN rail mounting

The Crestron® DIN-8SW8-I is an 8-channel lighting control module designed to support non-dimmable lighting and fan switching. The module features eight isolated digital inputs, allowing standard momentary switches to trigger events with or without a control system. A single model supports both 120V and 220-240V applications. Each channel handles incandescent loads up to 10A, fluorescent loads up to 5A, and 1/2 HP motor loads[1].Override InputOverride inputs are provided to allow an external contact closure to momentarily override the control system program and set each channel output to its override preset level. Levels can be adjusted and saved locally from the front panel or remotely via software.Isolated Local InputsThe DIN-8SW8-I provides eight isolated local inputs, allowing momentary pushbutton keypads to be used. By default, a momentary voltage applied to each input will cause the associated relay to toggle on/off. The attached Crestron control system can override this behavior and create eight general-purpose inputs. In this mode, pushbutton keypads can be programmed to provide customized functionality.DIN Rail InstallationThe DIN-8SW8-I is designed to snap onto a standard DIN rail for installation in a wall mount enclosure. Wiring connections are made using screw terminals positioned along the bottom, clearly accessible from the front for easy installation and servicing. All setup controls and indicators are positioned on the center front panel. When installed in an enclosure utilizing 45 mm cutouts, the DIN-8SW8-I's front panel stays accessible while the connections are concealed.Cresnet® Wired CommunicationsThe DIN-8SW8-I communicates with a Crestron® Control System using the Cresnet control network. A pair of Cresnet ports is provided on the DIN-8SW8-I, allowing for easy daisy-chaining of several DIN Rail Series automation control modules. Key Features8 channels of power switching8 voltage driven isolated digital inputs120 to 240VAC, 50/60 Hz operationOverride inputCresnet® wired communicationsSetup via front panel or softwareProgrammable functionality using a Crestron® Control System9M wide DIN rail mounting

The DIN-AO8 is a DIN rail-mounted automation control module that provides eight analog output ports for interfacing with third-party lighting and heating/cooling systems.Analog OutputsEach analog output port provides a 0 to 10 Volt DC control signal ideally suited for controlling 0-10V lighting dimmers and heating/cooling valves. Ten-bit resolution ensures precise recall of lighting and climate control settings and smooth ramping between levels.Override InputAn override input is provided to allow an external contact closure to momentarily override the control system program and set each output to its override preset level. Levels can be adjusted and saved locally from the front panel, or remotely via software.DIN Rail InstallationThe DIN-AO8 is designed to snap onto a standard DIN rail for installation in a wall mount enclosure or mounted on a wall panel. Wiring connections are made using detachable screw terminals positioned along the top and bottom, clearly accessible from the front for easy installation and servicing. All setup controls and indicators are positioned on the center front panel. When installed in an enclosure utilizing 45 mm cutouts, the DIN-AO8's front panel stays accessible while the connections are concealed.Cresnet®The DIN-AO8 communicates with a DIN-AP2 2-Series Automation Processor, or other Crestron 2-Series control system, via the Cresnet control network. Cresnet also powers the DIN-AO8. A pair of Cresnet ports is provided on the DIN-AO8 allowing for easy daisy-chaining of several DIN Rail Series automation control modules. Key FeaturesEight 0-10V analog output control portsInterface for 3rd-party lighting and heating/coolingFully programmable functionality via DIN-AP2Setup via front panel or softwareOverride inputCresnet communications6M wide DIN rail mounting

The DIN-CENCN-2-POE is an Ethernet to Cresnet® Network Bridge that works with a Crestron® Control System® to maximize the reliability and robustness of the Cresnet network. It offers a more sophisticated solution than a Cresnet block or hub, providing two isolated subnets and built-in diagnostics, plus versatile power distribution options and a convenient DIN rail form factor.NOTE: The DIN-CENCN-2-POE is not compatible with Crestron 2-Series control systems or earlier.The Cresnet BusCresnet is the communications backbone for many Crestron keypads, lighting controls, shade motors, thermostats, sensors, and other devices that don’t require the higher speed of Ethernet. It provides a dependable and flexible wiring solution, allowing multiple devices to be wired together in parallel using both home-run and daisy-chain topologies. The Cresnet bus distributes bidirectional data communication and 24VDC power to each device over a single 4-conductor cable.Ethernet to Cresnet BridgeAdding Ethernet to Cresnet bridges to a Crestron Control System enables the distribution of Cresnet over high-speed Ethernet. The increased bandwidth afforded by Ethernet reduces latency for overall improved speed and performance. Wiring distances can be extended easily while potentially reducing the overall wiring requirements by leveraging existing LAN infrastructure in any facility. One or more bridges can be deployed on a single control system, and they can even be addressed by more than one control system, affording incredible flexibility in system design and functionality.Dual Cresnet SubnetsThe DIN-CENCN-2-POE provides two isolated subnets. Each subnet behaves as a Cresnet Server with its own unique address space. A maximum of 20 Cresnet devices is supported per subnet, and each subnet furnishes six Cresnet connectors for easy termination of multiple lines. Crestron recommends a maximum aggregate cable length of 1500 feet (457 meters) per subnet.Cresnet Power DistributionProper power distribution is key to a reliable Cresnet network. To facilitate proper powering, the DIN-CENCN-2-POE offers versatile, scalable power management using PoE or 24VDC. 10 W total Cresnet power is available to both subnets using PoE, which can be increased to 20 W using PoE+. Adding one or two external 24VDC Cresnet power supplies enables up to 75 W Cresnet power to either or each subnet depending on the configuration. For more details, refer to the “Power” section of the specifications.The DIN-CENCN-2-POE configures itself automatically based on the power source(s) connected. Built-in protection intelligently monitors the load and wiring conditions on each subnet, and shuts down power to either subnet in case of an overload, wiring fault, or power supply failure. If such an error occurs, only the subnet with the error is shut down, leaving the other subnet fully operable.Diagnostics ToolsMany common control system problems are caused by wiring faults, insufficient power, or too many devices. The latter is resolved by increasing bandwidth using Ethernet and limiting the number of devices that can be connected to each subnet.For the other issues, the DIN-CENCN-2-POE provides a full set of diagnostic tools to help identify and resolve them easily.From the unit’s front panel, an installer can press the TEST button and observe the LED indicators to see if there are any error codes. This allows wiring problems to be identified before ever powering up the control system. More complete details can be viewed and analyzed using a web browser or Crestron Toolbox™ software.In a functioning system, sporadically occurring errors caused by cut or faulty wires, disconnected devices, or failed power supplies can be reported to the control system in real-time to provide error notifications via a touch screen, mobile device, email, or text message. For commercial enterprise applications, SNMP, and Crestron Fusion® Cloud applications are also supported. Insertion of an SD memory card (not included) enables logging of Cresnet activity and errors, making it easier to diagnose intermittent issues that cannot be duplicated on demand.Power over EthernetUsing PoE+ technology, the DIN-CENCN-2-POE gets its operating power through the LAN wiring from a PoE or PoE+ power source (PWE-4803RU, CEN-SW-POE-5, or CEN-SWPOE-16, sold separately). Alternately, the unit can be powered by 24VDC Cresnet power. Refer to the “Power” section of the specifications for more details.DIN Rail MountingThe DIN-CENCN-2-POE is designed to snap onto a standard 35 mm DIN rail for installation in a wall mount DIN-EN series enclosure or on any flat surface. DIN rail mounting affords a very space-efficient, cost-effective, and modular solution for configuring complete control systems using a Crestron control system along with additional Crestron and third-party DIN rail mountable devices. Key FeaturesMaximizes Cresnet® network reliability and performanceEnables Cresnet data communications over high-speed EthernetProvides two isolated Cresnet subnetsSupports 20 Cresnet devices per subnetSupports 1500 feet (457 m) aggregate cable length per subnetPowerable via PoE, PoE+, or CresnetIncludes intelligent power management for each subnetFeatures built-in network diagnostics toolsNetwork wiring, power, and communications testingDetailed error analysis via software or web browserReal-time error reporting via the control systemCresnet activity and error logging over time9M wide DIN rail mountable

The DIN‑DALI‑2 is a DALI‑2™ certified DALI® interface for Crestron® systems that provides control of up to 2 individual DALI loops. Housed in a DIN-rail enclosure, the DIN‑DALI‑2 is a low-profile Cresnet® or Ethernet companion to most Crestron DIN rail processors and control systems. In addition to controlling the DALI data bus, it includes an integrated DALI power supply. Single-wire connectivity simplifies both new and retrofit installations, and Power-over-Ethernet (PoE) versatility assists in situations with existing CAT5 infrastructure.This product is only available as part of a complete engineered and commissioned Crestron Green Light® system Contact Sales Support Services to obtain a quote for Factory Engineering Services and On-Site Commissioning.Two DALI ChannelsThe dual-channel DALI outputs on the DIN‑DALI‑2 makes controlling up to 128 individual DALI ballasts easy. The Digital Addressable Lighting Interface (DALI) is a protocol used for the control of lighting in buildings and is found on ballasts available from many manufacturers. Since it offers ballast-level control, lighting loads powered from the same feed can be controlled individually. DALI is a great choice for retrofit lighting systems because it does not require changes in line voltage wiring. Likewise, DALI provides ultimate flexibility by allowing reconfiguring of zones after a system is installed.Integrated DALI Power SupplyThe innovative design of the DIN‑DALI‑2 eliminates the need for the external power supplies required by other DALI controllers on the market. Power is delivered via PoE or Cresnet1, creating a true single-wire installation. Both Cresnet and PoE are capable of powering all 128 DALI ballast controllers. If desired, an external power supply may be used in conjunction with the DIN‑DALI‑2. An on-board switch allows the installer to choose the required mode during setup.Commissioning ToolDesigned specifically for the DIN‑DALI‑2, the Crestron DALI commissioning software tool facilitates system setup. The intuitive menu-driven wizard provides step-by-step configuration of ballast properties, groups, and scenes. Guided by the software, one can simply set the ballast address and check connectivity status, edit minimum/maximum levels and fade time, and change ballast groupings and scenes. This powerful software makes ballast replacement straightforward through automatic identification of new hardware IDs. Settings from old ballasts are transferred to replacements with just a few mouse clicks, saving time and eliminating guess work and frustration.Familiar Programming InterfaceControlling a DALI ballast is just like controlling any Crestron dimmer. Familiar visual Crestron configuration tools, as found in D3 Pro® and SIMPL, replace complex hardware addressing and communication protocols. Crestron D3 Pro software eliminates the need for custom programming, providing a complete design, development, and documentation solution for the lighting professional.Override InputAn override input is provided to allow an external contact closure to momentarily override the control system program and force each ballast into its defined System Failure Level. States can be set and saved locally from the front panel, or remotely via software.DIN Rail InstallationThe DIN‑DALI‑2 is designed to snap onto a standard DIN rail for installation in a wall mount enclosure. Wiring connections are made using screw terminals positioned along the top and bottom, clearly accessible from the front for easy installation and servicing. All setup controls and indicators are positioned on the center front panel. When the DIN‑DALI‑2 is installed in an enclosure utilizing 45 mm cutouts, the front panel stays accessible while the connections are concealed.Cresnet® and PoEThe DIN‑DALI‑2 communicates with a DIN‑DALI‑2 Automation Processor, or most other Crestron control systems, via the Cresnet control network or Power-over-Ethernet (PoE). A pair of Cresnet ports on the DIN‑DALI‑2 allows for easy daisy-chaining of several DIN Rail Series automation control modules. A standard Ethernet jack accommodates data and power to be delivered to the unit over one CAT5 cable.NOTE: The DIN‑DALI‑2 is not compatible with Crestron 2‑Series control systems or earlier. Key FeaturesInterfaces with 2 independent DALI® loopsDALI-2™ certifiedControls up to 128 DALI ballastsCresnet® or PoE communication for single-wire installationIntegrated DALI power supplyCrestron® DALI commissioning tool for easy setupOverride input9M wide DIN rail mountingCEC Title 24 2013 Compliant

The Crestron® DIN-DMX-1UNIVERSE is a Pharos LPC (Lighting Playback Controller) all-in-one control solution for themed entertainment and LED lighting installations.Pharos EngineThe intelligent Pharos Engine gives you complete control of your installation. The DIN-DMX-1UNIVERSE provides individually controllable and independently running timelines and scenes allowing you to build dynamic, precise, and fully customizable preprogrammed lighting displays. Additionally, it provides you with the freedom of real-time manual overrides, flexible multizone control, prioritization, and more.Pharos MappingDesign the big picture — control every pixel. Create a map of your fixtures within the Designer software, then use Pharos Mapping to create visually striking effects or play video across the entire array. Powerful controls allow you to build maps fast with pixel-precise adjustment. Multiple maps can be created to support different zones or for modeling different views of your installation.Pharos TriggerControl your lighting with responsive, reactive programming. Pharos Trigger is a rules engine that uses conditional logic and a broad range of interfaces and protocols. Send and receive any command to and from any system. Conditional logic is supported, along with a powerful built-in scripting language for unlimited flexibility.Scalable for Any InstallationThe right fit for every installation. Multiple Pharos controllers can be seamlessly linked together to work as one via a standard Ethernet network giving impressive scalability. For additional integration options, add remote devices to extend the network further. Whether one controller or many, it’s all easily programmed using our Designer software.Remote ManagementThe control you need in your browser — from anywhere. Pharos Controllers can be connected to a network, making it possible for you to manage your installation remotely. The built-in web server lets you check the Controller’s status, inputs and outputs, trigger timelines, view a full history log, and more.Handles Multiple Lighting ProtocolsBe limited by your design brief, not your control system. The DIN-DMX-1UNIVERSE supports a vast range of different fixture types and can output multiple DMX-over-Ethernet (eDMX) lighting protocols at the same time to provide an unparalleled level of flexibility and control over your project.DIN Rail MountingThe DIN-DMX-1UNIVERSE is designed to snap onto a standard DIN rail for installation in a wall mount enclosure (Crestron DIN-EN series or similar, not supplied) or on a wall panel. Key FeaturesPharos engine for complete control of the installationBuild dynamic, precise, fully customizable pre-programmed lighting displays512 DMX/eDMX Channels, 1 UniverseScalable to the size of your lighting displayControl a wide range of devicesReliable 24/7 operation8U 35 mm DIN rail mountable

The Crestron® DIN-DMX-1UNIVERSE is a Pharos LPC (Lighting Playback Controller) all-in-one control solution for themed entertainment and LED lighting installations.Pharos EngineThe intelligent Pharos Engine gives you complete control of your installation. The DIN-DMX-1UNIVERSE provides individually controllable and independently running timelines and scenes allowing you to build dynamic, precise, and fully customizable preprogrammed lighting displays. Additionally, it provides you with the freedom of real-time manual overrides, flexible multizone control, prioritization, and more.Pharos MappingDesign the big picture — control every pixel. Create a map of your fixtures within the Designer software, then use Pharos Mapping to create visually striking effects or play video across the entire array. Powerful controls allow you to build maps fast with pixel-precise adjustment. Multiple maps can be created to support different zones or for modeling different views of your installation.Pharos TriggerControl your lighting with responsive, reactive programming. Pharos Trigger is a rules engine that uses conditional logic and a broad range of interfaces and protocols. Send and receive any command to and from any system. Conditional logic is supported, along with a powerful built-in scripting language for unlimited flexibility.Scalable for Any InstallationThe right fit for every installation. Multiple Pharos controllers can be seamlessly linked together to work as one via a standard Ethernet network giving impressive scalability. For additional integration options, add remote devices to extend the network further. Whether one controller or many, it’s all easily programmed using our Designer software.Remote ManagementThe control you need in your browser — from anywhere. Pharos Controllers can be connected to a network, making it possible for you to manage your installation remotely. The built-in web server lets you check the Controller’s status, inputs and outputs, trigger timelines, view a full history log, and more.Handles Multiple Lighting ProtocolsBe limited by your design brief, not your control system. The DIN-DMX-1UNIVERSE supports a vast range of different fixture types and can output multiple DMX-over-Ethernet (eDMX) lighting protocols at the same time to provide an unparalleled level of flexibility and control over your project.DIN Rail MountingThe DIN-DMX-1UNIVERSE is designed to snap onto a standard DIN rail for installation in a wall mount enclosure (Crestron DIN-EN series or similar, not supplied) or on a wall panel. Key FeaturesPharos engine for complete control of the installationBuild dynamic, precise, fully customizable pre-programmed lighting displays512 DMX/eDMX Channels, 1 UniverseScalable to the size of your lighting displayControl a wide range of devicesReliable 24/7 operation8U 35 mm DIN rail mountable

NOTE: The DIN‑GWDL is a gateway for DMX-C light fixtures available from Crestron and compatible third-party light fixtures. To order as part of a configured system, use the Light Fixture Configuration Tool or call 1-888-273-7876 (option 3) for Sales Support Services and/or your Regional Sales Manager. This gateway requires Crestron Home. This gateway is not compatible with DMX512 fixtures.The DIN‑GWDL is a gateway for Crestron light fixtures and Crestron compatible third-party light fixtures. It provides full control of all connected lighting loads. The DIN‑GWDL is configured using the Crestron Home Setup application and controlled using a Crestron Home system.Crestron Home Color UIUse the Crestron Home Color UI to easily control the tunable white and full color lighting loads. Adjust hue, saturation, intensity and color temperature. Create scenes to set the mood for entertaining or ensure the optimal setting for a professional conference call. Set lighting schedules or implement Circadian lighting rhythms.Circadian Rhythm Lighting ControlSunlight has a predictable rhythm of color temperature and intensity. Connected light fixtures can be synchronized with this natural rhythm.SolarSync® SensorMatch outside light using an outdoor SolarSync® photosensor (GLS-LCCT, sold separately). SolarSync communicates the outside color temperature to Crestron Home in real-time and tunes your indoor lighting accordingly.DMX-C ControlBuilt on the DMX512 standard, DMX-C offers the speed and reliability of a traditional DMX system with the seamless and consistent user experience of the Crestron Home OS. When connected to a DIN‑GWDL, DMX-C lighting fixtures are auto-discovered, auto-addressed, and treated as native Crestron devices with a consistent and intuitive interface.Supports up to 85 Crestron Light Fixtures and Crestron compatible third-party light fixtures with DIN-GWDL-SPLTR (sold separately)The DIN‑GWDL has two DMX-C outputs, each of which supports up to 32 directly connected Crestron light fixtures and Crestron compatible third-party light fixtures, for a total of 64 directly connected fixtures. Each added DIN‑GWDL‑SPLTR adds four additional DMX-C outputs, each of which supports up to 32 directly connected Crestron light fixtures and Crestron compatible third-party light fixtures. The DIN‑GWDL with a DIN‑GWDL‑SPLTR can support a total of 85 Crestron light fixtures and Crestron compatible third-party light fixtures.Fast CommissioningConnect Crestron light fixtures and Crestron compatible third-party light fixtures quickly with the RJ-45 adapters. Verify the system immediately by testing lighting loads with local controls. Once connected to a Crestron Home processor, DMX-C allows for lighting loads to be automatically addressed and discovered using the fixture identify tool.Local ControlAdjust intensity or turn all connected fixtures on and off through local control on the DIN‑GWDL.  Key FeaturesDesigned exclusively for Crestron Home® OSSupports up to 64 directly connected Crestron light fixtures and Crestron compatible third-party light fixturesSupport expanded up to 85 Crestron light fixtures and Crestron compatible third-party light fixtures with the use of a DIN-GWDL-SPLTR (sold separately)RJ-45 adapters included for quick wiring using standard CAT5 cableAbility to turn all lights on and off without a control system via local controlAuto-addressing and quick commissioning through the Crestron Home Setup ApplicationCompatible with Crestron SolarSync® sensorsOrder using the Crestron Light Fixture Configuration Tool6U 35 mm DIN rail mountable

The DIN-HUB is a DIN rail-mounted Cresnet hub designed to facilitate the configuration of large Cresnet networks. DIN rail mounting enables modular installation alongside Crestron DIN Rail lighting and automation control modules and other third-party DIN rail mountable devices.3-Segment Cresnet® HubCresnet is the communications backbone for Crestron lighting modules, wall box dimmers, shade controllers, thermostats, keypads, touchpanels, and many other devices. This flexible 4-wire bus normally supports approximately 20 Cresnet devices without requiring a hub. Larger systems are easily enabled by adding the DIN-HUB. The DIN-HUB features 3 isolated Cresnet segments, each supporting an additional 20 devices, allowing for systems of approximately 80 devices total (including the "host" segment). More hubs may be added to allow up to a maximum potential of 252 devices.*Cresnet Power DistributionIn addition to data, Cresnet carries 24 Volts DC for powering the devices connected to it. The DIN-HUB provides an easy way to manage the distribution of power for a complete Cresnet network. Each segment can be configured to receive its power from the "host" power source or from another power supply. Separate power supplies may be dedicated to each segment, or a single supply can be shared amongst multiple segments as needed. Each segment supports up to 75 Watts.DIN Rail InstallationThe DIN-HUB is designed to snap onto a standard DIN rail for installation in a wall mount enclosure or mounted on a wall panel. Wiring connections are made using detachable screw terminals positioned along the top and bottom, clearly accessible from the front for easy installation and servicing. Diagnostic indicators are positioned on the center front panel. When installed in an enclosure utilizing 45 mm cutouts, the DIN-HUB's front panel stays visible while the connections are concealed. Key Features3-segment Cresnet hubFor Cresnet networks with more than 20 devicesConfigurable power distributionNo programming required6M wide DIN rail mounting

The DIN-KXI is an IP-based KNX interface that allows a 4-Series® control system to communicate with a KNX system. It is capable of addressing and controlling up to 1,000 datapoints and receives power over the KNX bus. The DIN-KXI can also be used as a programming interface for KNX devices using ETS5 or ETS6 software.KNX SecurityThe device supports KNX Security (AES-128) which can be enabled using ETS software.Ethernet CommunicationsThe Ethernet connection allows access to the KNX bus from any point on the LAN. This provides programming and diagnostics without direct access to the DIN-KXI. Local DiagnosticsThe buttons and LEDs on the device provide diagnostic data including the operating status and communication errors.DIN Rail InstallationThe 1M (18 mm) wide DIN-KXI snaps onto a standard DIN rail for installation in a wall mount enclosure. Wiring connections are made along the top and bottom, clearly accessible from the front for easy installation and servicing. All setup controls and indicators are positioned on the center front panel. Key Features1M wide DIN rail mountingEthernet to KNX interfaceIntegrates KNX with a Crestron® control systemSupports KNXnet/IP Security (AES-128)Controls up to 1,000 KNX datapointsUp to 8 simultaneous KNXnet/IP Tunneling connectionsConfigure using ETS SoftwareOn-board controls for setup and diagnosticsPowered via the KNX bus

The DIN-PWS60 is a 60 Watt Cresnet® Power Supply module designed to snap onto a standard DIN rail for installation in a wall-mount enclosure. DIN rail mounting enables modular installation alongside Crestron® DIN Rail lighting and automation control modules and other third-party DIN rail-mountable devices. All wiring connections are made using screw terminals positioned along the top and bottom of the unit, which are clearly accessible from the front for easy installation and servicing. Six Cresnet power ports are provided. Key Features60 Watt Cresnet® power supply modulePowers the DIN-AP3 Automation Processor and other Cresnet devicesIncludes six Cresnet power portsCresnet data passes through unaffected6M wide DIN rail mounting100-277 Volt AC line powered

The Crestron DIN-SACN-DMX (sold by ENTTEC as model DIN Ethergate Mk2) is a cost-effective and reliable Ethernet to DMX convertor. It supports sACN, Art-Net, and ESP protocols, and integrates DMX and network controllable lighting devices and systems. As part of a Crestron architectural lighting system, it allows a 3-Series® or 4-Series™ control processor to communicate via sACN with any DMX lighting fixture or controller.The DIN-SACN-DMX's electrically insulated housing supports TS35 DIN and surface mounting for fast installation. In addition, pluggable terminal blocks with an inbuilt termination line make wiring simple. Key FeaturesConverts between DMX512A and sACN, Art-Net, and ESP protocolsEnables distribution of DMX over a Ethernet or Wi-Fi® networkEnables control of DMX lighting fixtures and systems by Crestron devicesSupports a single universe Ethernet to DMX node in output modeSupports a single universe DMX to Ethernet node in input modeSupports broadcast or unicast (unicast in input mode only)Supports HTP/LTP merging of up to 2 DMX sources (output mode only)Supports RDM over Art-NetEasy web browser-based setup and firmware updates4U 72 mm DIN rail mountablePoE or 12-24VDC powered (power supply not included)