HD-RXCA-4KZ-101

The DM‑NAX‑BTIO‑1G is a DM NAX® encoder and decoder with support for Bluetooth wireless input and analog line-level wired audio input and output, housed in a single-gang wall plate form factor. The front panel features an OLED display and four buttons for device pairing and menu navigation. Two 1/8 in. (3.5 mm) TRS connectors for stereo unbalanced analog line-level audio input and output are concealed under a front panel door. The rear panel of the wall plate features an Ethernet connection for PoE, Audio over IP (AoIP), and control.DM NAX is built on the AES67 standards with additional ease of configuration via a web interface, SIMPL Windows, C#, and/or a RESTful API. It is compatible with DM NVX through the AES67 secondary audio stream and also with third-party AES67 solutions and Dante via the compatibility mode enabled through Dante Controller.Bluetooth Wireless ConnectivityBluetooth wireless audio input support is built-in to the DM‑NAX‑BTIO‑1G, allowing a stereo audio signal (such as an album or podcast) to be transmitted from a smart phone or other source device to the wall plate. This signal can be output as a DM NAX AoIP stream onto the network to distribute the content throughout several rooms or as an unbalanced line-level analog signal from the local 3.5 mm audio output connector. Metadata for the Bluetooth audio stream can be displayed on the front panel, and up to seven previous source device connections can be recalled.Audio-over-IPDM NAX takes audio distribution to a whole new level by putting it on the network. The DM‑NAX‑BTIO‑1G sends and receives DM NAX and AES67 encoded audio over a standard IP network. A single DM NAX system can handle audio distribution between 32 DM NAX devices and supports up to 256 audio output zones. DM NAX devices can seamlessly pull and distribute the audio from DM NVX sources.Encoder and Decoder FunctionalityThe DM‑NAX‑BTIO‑1G can operate as a network AV encoder and decoder. The local input sources on the wall plate can be sent as AoIP streams to DM NAX, Dante, or AES67 capable devices. Simultaneously, the DM‑NAX‑BTIO‑1G can receive AoIP streams from these same devices and decode them for local output.NOTE: As a decoder, the DM-NAX-BTIO-1G can only locally output audio via the line-level output. The DM-NAX-BTIO-1G does not support local output via Bluetooth wireless audio.Front Panel Controls and DisplayThe DM‑NAX‑BTIO‑1G features four front panel push buttons and a 128 x 64 dot matrix OLED display. The push buttons allow local volume control and Bluetooth pairing, with volume feedback and pairing status reflected in real time on the display. Metadata for Bluetooth media and basic configuration menus are also shown on the display.Both the display and push buttons can be disabled via the configuration web interface or programming for applications where a more discreet or secure installation is required. Key FeaturesBuilt-in Bluetooth® wireless audio input supportFront panel OLED display provides metadata readout and device setup menusSingle-gang U.S. wall box installationPower over Ethernet (PoE) network poweredStereo unbalanced analog line-level audio input and output via 3.5 mm TRS connectorsMountable in a standard US electrical box or on a rack rail via included hardwareConnects directly to a managed network to route to or from other DM NAX® and DM NVX® devicesInteroperable with Dante® audio networking devices via AES67 compatibilityStreamlined configuration through front panel push buttons and a web interfaceSeamless Crestron system integration with SIMPL Windows programming

The DM-TX-4KZ-100-C-1G wall plate transmitter provides a cost-effective solution for a single AV source as part of a complete Crestron® DigitalMedia™ system. Functioning as a DM 8G+® transmitter and control interface, the DM-TX-4KZ-100-C-1G provides an HDMI® input and a DM 8G+ output as well as IR and RS-232 control ports. The DM-TX-4KZ-100-C-1G incorporates DM 4KZ technology, which enables 4K60 4:4:4 and HDR (High Dynamic Range) support.1 The DM-TX-4KZ-100-C-1G is also compatible with HDBaseT® technology.The DM-TX-4KZ-100-C-1G wall plate transmitter provides a 1‑gang mountable design and is available in white (DM-TX-4KZ-100-C-1G-W-T) and black (DM-TX-4KZ-100-C-1G-B-T).4K60 4:4:4 and HDR SupportDM 4KZ technology uses VESA® Display Stream Compression (DSC) to handle the extreme bandwidth requirement of resolutions beyond 4K30 4:4:4 and 4K60 4:2:0. DSC is a lightweight, line-based 2:1 compression standard that delivers visually lossless performance for 4K60 4:4:4 and HDR signals.1 DSC is applied only to 4K60 4:4:4 and HDR input signals. All other signals are transported uncompressed.An existing 4K DigitalMedia system can be upgraded to handle 4K60 4:4:4 and HDR video with the installation of DM 4KZ cards, transmitters, and receivers. The upgrade can be accomplished without the need to replace wiring or switchers. The DM-TX-4KZ-100-C-1G can replace a DM-TX-4K-100-C-1G in an existing installation (additional programming may be required).DM 8G+ TechnologyEngineered for ultra high-bandwidth and ultimate scalability, Crestron DM 8G+ technology transports high-definition video, audio, power, Ethernet, and control signals over twisted pair copper wire. Uncompressed Full HD 1080p, WUXGA, and 2K signals are supported at distances up to 330 ft (100 m) using Crestron DM® Ultra cable, Crestron DM 8G® cable, or third-party CAT5e (or higher). Higher resolution signals up to UHD and 4K are supported at distances up to 330 ft (100 m) using DM Ultra cable, 230 ft (70 m) using DM 8G cable, or 165 ft (50 m) using third-party CAT5e (or higher).2HDBaseT CompatibilityDM 8G+ technology is designed using HDBaseT Alliance specifications, ensuring interoperability with other HDBaseT certified products. Via the DM 8G+ output, the DM-TX-4KZ-100-C-1G can be connected directly to a third-party HDBaseT compliant receiver or display device without requiring a DM receiver.Multimedia Computer/AV InterfaceA single HDMI input port is provided on the DM-TX-4KZ-100‑C-1G for connection to a laptop computer, mobile device, or other AV source.3 A single CAT5e (or higher) cable connects the DM-TX-4KZ-100-C-1G to a DM switcher or receiver or to an HDBaseT device. Video, audio, control, networking, and power signals are transported through one RJ-45 connection.2, 4, 5 When used with a DM switcher, multiple DM-TX-4KZ-100-C-1G devices can be installed, enabling several AV input signals at different locations to be transmitted to multiple displays throughout a room or larger facility. When used with a single DM 8G+ receiver/room controller, the DM-TX-4KZ-100-C-1G extends an AV signal to a single display.Device ControlThe DM-TX-4KZ-100-C-1G includes built-in IR and RS-232 control ports to enable programmable control of the connected source device via a control system.6 When connected to a control system, the DM-TX-4KZ-100-C-1G also provides a gateway for controlling the AV source through CEC (Consumer Electronics Control) over the HDMI input, potentially eliminating the need for a dedicated serial cable or IR emitter.Pass-through mode for RS-232 and CEC is also supported. For additional information, refer to Online Help Answer ID 1000497 on the Crestron website (www.crestron.com).Versatile Mounting OptionsThe DM-TX-4KZ-100-C-1G is designed to be mounted into a 1‑gang electrical box or plaster ring (not included). Standard gang-box mounting enables installation adjacent to an Ethernet jack (Crestron MP-WP183 or equivalent).7Using the included mounting bracket, the DM-TX-4KZ-100‑C-1G can also be attached to a suitable flat surface such as the underside of a table. As an additional mounting option, the DM‑TX-4KZ-100-C-1G can be attached to a single rack rail.Power via the DM connection can be used to power the DM‑TX-4KZ-100-C-1G. The device can also be powered using the optional PW-2407WUL wall mount power pack (sold separately).For additional design tools and reference documents, refer to the DigitalMedia resources web page at http://www.crestron.com/dmresources. Key Features4K60 4:4:4 supportHDR10, Deep Color, and 3D videoDolby® TrueHD, Dolby Atmos®, DTS HD®, and uncompressed 7.1 linear PCM audioHDBaseT® compatibilityHDCP 2.2 complianceHDMI® input (DVI and Dual-Mode DisplayPort™ interface compatible)DM 8G+® output for connection to a DM® switcher or receiver via a single CAT5e (or higher) twisted pair cableTransmission distance up to 330 ft (100 m) for resolutions up to UHD and 4K using DM Ultra cableTransmission distance up to 330 ft (100 m) for 1080p, WUXGA, and 2K using DM 8G® cable or CAT5eTransmission distance up to 230 ft (70 m) for UHD and 4K using DM 8G cable or up to 165 ft (50 m) using CAT5eDevice control via CEC, IR, and RS-232Powered via the DM connection or optional power pack (sold separately) Versatile mounting options including 1-gang electrical box, surface mounting, and attachment to rack railSurface-mount bracket includedWhite finish

The Crestron HD-CONV-USB-300 converts an HDMI® signal to USB 3.0. The device captures uncompressed 1080p60 video with stereo digital or analog audio. USB capture is accomplished using the USB Video Class (UVC) and USB Audio Class (UAC) standards, which are compatible with the most common video capture or streaming software applications. Input resolutions larger than Full HD and up to 4K UHD are automatically scaled to 1080p for USB capture. Video timing stabilization helps to ensure a reliable and stable USB capture stream.   The HD-CONV-USB-300 can be used for standalone video conversion or as part of an integrated UC (unified communications) solution. By using the HDMI output and analog audio input, you can leverage existing video conferencing equipment in the room. For example, if you need to install a secondary UC codec to an existing installation, you can share the microphone and HDMI camera devices by feeding these signals into the HD-CONV-USB-300. The HDMI output can connect the camera signal back to the existing UC codec while the captured USB stream feeds into the new UC codec.   You can also install this device in an existing video conferencing room to add BYOM (Bring Your Own Meeting) capability. Simply connect the room’s microphone and HDMI camera to the HD-CONV-USB-300 and connect via USB to the user’s laptop to start the meeting from a soft codec while using the room’s superior camera and microphone,     Key Features Converts a 4K60 4:4:4 HDMI® input to a USB 3.0 output Captures uncompressed 1080p60 video and stereo audio over USB 3.01 Supports deep‑color and HDR up to 12‑bit HDCP 2.2 and HDCP 1.x compliant on HDMI input and output2 Automatically downscales 4K sources to 1080p for USB capture Supports capturing 2‑channel digital audio from either HDMI (LPCM 2.0) or the 3.5 mm analog audio input Compliant with the USB Audio Class (UAC) and USB Video Class (UVC) standards HDMI output port for local viewing or loop‑through functionality Compact surface‑mountable housing

The Crestron® HD-DA8-4KZ-E is a simple to use, high-performance 4K AV distribution amplifier designed to split a single HDMI® signal to feed up to eight separate displays, switchers, and/or other devices. It provides full support for UHD and DCI 4K60 4:4:4 and HDR video, HDCP 1.4 or 2.2 copy protection, and high-bitrate 7.1 audio, to ensure optimal performance and compatibility for any HD or 4K video application. No programming or control system is required for operation.[1]   For smaller applications, refer to models HD-DA2-4KZ-E and HD-DA4-4KZ-E.     Key Features Splits one HDMI® source to eight outputs Handles 4K60 4:4:4 and HDR video signals [1] Fully compatible with HD 1080p, UHD 4K, and DCI 4K sources and displays Handles 3D video and Deep Color Handles Dolby® TrueHD, Dolby Atmos®, DTS HD®, DTS:X®, and uncompressed 7.1 linear PCM audio Selectable handling of HDCP 2.2 or HDCP 1.4 EDID management options Input and output video presence indication No programming or control system required Thin profile – less than one inch deep Surface, shelf, or single rack rail mountable External 100-240V universal power pack included

The HD-MD4X1-4KZ-E is a 4K60 4:4:4 HDR (High Dynamic Range) AV switcher that provides a cost-effective solution for professional AV applications. Equipped with four HDMI® inputs and one HDMI output, the HD-MD4X1-4KZ-E includes features such as automatic switching of inputs, EDID management, HDCP 2.3 compliance, enterprise-grade security, and XiO Cloud® service support.   4K60 4:4:4 and HDR Support The HD-MD4X1-4KZ-E supports video resolutions up to 4K60 with 4:4:4 color sampling. HDR10, HDR10+, and Dolby Vision® video formats are also supported.   Automatic Switching of Inputs Automatic switching among the HDMI inputs can occur based on the last connected input or on the routing priority assigned to each input.   Switching behavior is configurable using the web interface or the XiO Cloud® service and is programmable using a Crestron control system. In addition, input selection push buttons on the front panel of the HD-MD4X1-4KZ-E enable the desired inputs to be selected manually.   EDID Management The HD-MD4X1-4KZ-E provides comprehensive management of EDID (Extended Display Identification Data) to ensure that every source is displayed at the optimal resolution and format. For applications requiring a custom configuration, the HD-MD4X1-4KZ-E enables assessment of the format and resolution capabilities of any device that is connected to the HDMI output of the switcher. The HD-MD4X1-4KZ-E provides the ability to configure signals appropriately for the most desirable and predictable behavior.   HDMI Audio De-embedding Embedded HDMI 2-channel LPCM audio can be extracted from the selected HDMI input and transmitted to the AUX stereo audio output. Volume and mute control are configurable for the HDMI output and AUX audio output.   Device Control via CEC Under the management of a control system, CEC (Consumer Electronics Control) over the HDMI connections can control the source and display devices, potentially eliminating the need for dedicated serial cables or IR emitters. CEC over the HDMI output can also enable the display device to be turned on or off automatically without the use of a control system.   Enterprise-Grade Security The HD-MD4X1-4KZ-E includes advanced security features and protocols. Using 802.1X authentication, Active Directory® credential management, PKI authentication, TLS, SSH, and HTTPS, the HD-MD4X1-4KZ-E provides a true enterprise-grade AV switcher.   Built-In Web Interface Configuration of the HD-MD4X1-4KZ-E can be accomplished by using the built-in web interface. The configuration of a single unit can be downloaded to a computer or mobile device and then uploaded to multiple HD-MD4X1-4KZ-E units to simplify system installation.   .AV Framework™ Technology Support In addition to a built-in web interface and control system programming, built-in .AV Framework technology of a Crestron control system can be used to configure and control the HD-MD4X1-4KZ-E. For information about .AV Framework technology and the supported Crestron control systems, visit www.crestron.com/avframework.   XiO Cloud® Service Support The HD-MD4X1-4KZ-E is compatible with the XiO Cloud service, which is an IoT (Internet of Things) platform for remotely provisioning, monitoring, and managing Crestron devices across an enterprise or an entire client base. Built on the Microsoft® Azure® software platform and using industry-leading Azure IoT Hub technology, the XiO Cloud service enables installers and IT managers to deploy and manage thousands of devices in the amount of time it previously took to manage a single device. Unlike other virtual machine-based cloud solutions, Azure services provide unlimited scalability to suit the ever-growing needs of an enterprise. For more information, visit www.crestron.com/xiocloud.   Compact Surface-Mountable Design The HD-MD4X1-4KZ-E can be mounted to a wall or other flat surface. It can also be attached to a single rack rail.     Key Features 4K60 4:4:4 digital AV switcher HDR10, HDR10+, and Dolby Vision® video formats Four HDMI® inputs and one HDMI output Automatic switching of inputs EDID management HDCP 2.3 compliance HDMI audio de-embedding Device control via CEC Enterprise-grade security Built-in web interface Compatibility with Crestron® 3-Series® or later control systems .AV Framework™ technology support XiO Cloud® service support Compact surface-mountable design PoE powered device (optional power pack sold separately)

The HD‑RXC‑4KZ‑101 is a DM® Essentials 4K60 4:4:4 receiver designed to interoperate with a DM® Essentials transmitter or DMPS Essentials switcher for the transmission of HDMI®, RS-232, and IR signals. A CAT5e or higher twisted pair cable (Crestron DM‑CBL‑8G or DM‑CBL‑ULTRA sold separately) is needed to connect the HD‑RXC‑4KZ‑101 to the DM Essentials transmitter or DMPS Essentials switcher. For 1080p, WUXGA, and 2K signals, a cable length of up to 230 ft (70 m) is supported. For UHD and 4K signals, a cable length of up to 130 ft (40 m) is supported.1   Interoperability with a DM Essentials Transmitter or DMPS Essentials Switcher The DM Essentials input port of the HD‑RXC‑4KZ‑101 must be connected to a DM Essentials output port of a DM Essentials transmitter or DMPS Essentials switcher. Examples of supported DM Essentials 4K60 4:4:4 transmitters are the HD‑TXC‑4KZ‑101 and HD‑TXCA‑4KZ‑101. Supported DMPS Essentials switchers are the HD‑PS622, HD‑PS621, HD‑PS402, and HD‑PS401.   The HD‑RXC‑4KZ‑101 can be configured and controlled only when it is used with a DMPS Essentials switcher. The web interface of the switcher can be used to configure the HD‑RXC‑4KZ‑101. In addition, control system programming and .AV Framework™ software support of the HD‑RXC‑4KZ‑101 is hosted by the switcher.   4K60 4:4:4 and HDR Support The HD‑RXC‑4KZ‑101 supports video resolutions up to 4K60 with 4:4:4 color sampling. HDR10, HDR10+, and Dolby Vision® video formats are also supported.2   Compact, Surface-Mountable Design Compact in design, the HD‑RXC‑4KZ‑101 can be mounted onto a flat surface such a wall behind a flat-panel display or a ceiling above a projector. It can also be attached to a single rack rail in the back of an equipment cabinet. The HD‑RXC‑4KZ‑101 can receive power from the included power pack or from the remote DM Essentials transmitter or DMPS Essentials switcher.3     Key Features Interoperability with a DM® Essentials transmitter or DMPS Essentials switcher Point-to-point extension of HDMI®, RS-232, and IR signals over a CAT5e or higher cable DM Essentials transmission distance up to 130 ft (40 m) for UHD and 4K signals or up to 230 ft (70 m) for 1080p, WUXGA, and 2K signals 4K60 4:4:4 capability HDR10, HDR10+, and Dolby Vision® video formats Compliance with HDCP 2.3 CEC (Consumer Electronics Control) pass-through capability Bidirectional RS-232 and IR pass-through capability EDID pass-through capability Compact, surface-mountable design Power from 24VDC power pack (included) or from remote DM Essentials transmitter or DMPS Essentials switcher

The HD-TX-201-C-2G-E (-B-T or -W-T) is a DM Lite® wall plate transmitter designed to pair with a DM Lite or DMPS Lite™ receiver to form a signal extender for HDMI® signals. The DM Lite family of products offers a versatile solution for extending HD, UHD, 2K, and 4K video signals, with stereo or surround sound audio, over a single CAT5e (or higher) cable. A cable length of up to 230 ft (70 m) is supported for HD 1080p, WUXGA, and 2K signals, or up to 130 ft (40 m) for UHD and 4K.1   In addition to its HDMI input, the HD-TX-201-C-2G-E also includes a VGA input accompanied by a stereo analog audio input. Auto-switching between HDMI and VGA enables plug-and-play simplicity. Manual input selection is also available using the front panel INPUT SEL button. The VGA input can accept RGB and component video signals by using an appropriate breakout cable or adapter (not included). The audio input is selected in tandem with the VGA input, and can be used by itself with no video source connected. However, it cannot be paired with the HDMI video input.   NOTE: When paired with an HD-RX-201-C-E or DMPS Lite receiver, the local inputs are switched in combination with the HDMI input on the receiver, and can also be controlled remotely through integration with a Crestron® control system.   A CAT6a RJ-45 courtesy jack is included to provide a 1000BASE-T network connection for computers and other devices. The front panel jack passes through to a parallel jack on the rear, which connects to an available port on the customer’s LAN. This LAN jack is provided as a convenience to replace the need for a separate RJ-45 wall jack. It does not interface with the DM Lite system and cannot be used to extend Ethernet signals or interface with a control system.   The HD-TX-201-C-2G-E series is available in black or white, and is designed to mount into a 2-gang electrical box or plaster ring (not included). When paired with a surface-mountable receiver, the HD-TX-201-C-2G-E is powered by the receiver over the DM Lite link cable.2   Note: This product is not addressable from a control system and offers no programmable functionality except when paired with an HD-RX-201-C-E or DMPS Lite receiver. Otherwise, AV and CEC signals are simply passed through between the transmitter and receiver. The RJ-45 link port on this product is exclusively intended for linking with a single DM Lite or DMPS Lite receiver. It should not be used to connect to any other equipment or network. DM Lite technology is not compatible with PoE, PoDM, DigitalMedia 8G+®, or HDBaseT® technology.     Key Features Pairs with a DM Lite® or DMPS Lite™ receiver Enables extension of HDMI® video and audio signals Converts and extends VGA and analog audio signals Auto-switches between one HDMI input and one VGA input Links to the receiver via a single CAT5e (or higher) twisted pair cable Supports 4K and UHD at up to 130 ft (40 m) Supports HD 1080p, WUXGA, and 2K at up to 230 ft (70 m) Handles 4K video resolutions up to 4K60 4:2:0 and 4K30 4:4:4 Handles 3D video and Deep Color Supports Dolby® TrueHD, Dolby Atmos®, DTS HD®, DTS:X®, and uncompressed 7.1 linear PCM audio Compatible with HDMI, DVI, and Dual-Mode DisplayPort™ sources Compatible with VGA, RGBHV, RGBS, RGsB, and YPbPr component sources up to HD 1080p and WUXGA HDCP 1.4 compliant Passes CEC and EDID signals Allows control system integration when paired with an HD-RX-201-C-E or DMPS Lite receiver Courtesy LAN jack Flush wall mount design Installs in a 2-gang U.S. electrical box (2-1/4” deep) or plaster ring (not included) Decorator style faceplates sold separately (type FP-G2-DM only) Normally powered by the receiver (surface-mountable) over the link cable

The HD‑TXCA‑4KZ‑101 is a DM® Essentials 4K60 4:4:4 transmitter designed to interoperate with a DM® Essentials receiver or DMPS Essentials switcher for the transmission of HDMI®, RS-232, IR, and analog audio signals. A CAT5e or higher twisted pair cable (Crestron DM‑CBL‑8G or DM‑CBL‑ULTRA sold separately) is needed to connect the HD‑TXCA‑4KZ‑101 to the DM Essentials receiver or DMPS Essentials switcher. For 1080p, WUXGA, and 2K signals, a cable length of up to 230 ft (70 m) is supported. For UHD and 4K signals, a cable length of up to 130 ft (40 m) is supported.1Interoperability with a DM Essentials Receiver or DMPS Essentials SwitcherThe DM Essentials output port of the HD‑TXCA‑4KZ‑101 must be connected to a DM Essentials input port of a DM Essentials receiver or DMPS Essentials switcher. Examples of supported DM Essentials 4K60 4:4:4 receivers are the HD‑RXC‑4KZ‑101 and HD‑RXCA‑4KZ‑101. Supported DMPS Essentials switchers are the HD‑PS622, HD‑PS621, HD‑PS402, HD‑PS401, and HD‑RX‑4K‑210‑C‑E.Note: When paired with an HD-RX-4K-210-C-E(-POE), the transmitter cannot provide power to the receiver. Power must be connected to the HD-RX-4K-210-C-E(-POE) only.The HD‑TXCA‑4KZ‑101 can be configured and controlled only when it is used with a DMPS Essentials switcher. The web interface of the switcher can be used to configure the HD‑TXCA‑4KZ‑101. In addition, control system programming and .AV Framework™ software support of the HD‑TXCA‑4KZ‑101 is hosted by the switcher.4K60 4:4:4 and HDR SupportThe HD‑TXCA‑4KZ‑101 supports video resolutions up to 4K60 with 4:4:4 color sampling. HDR10, HDR10+, and Dolby Vision® video formats are also supported.2Analog Audio EmbeddingThe analog audio input port of the HD‑TXCA‑4KZ‑101 enables a balanced/unbalanced stereo audio source to be embedded with the video signal from the HDMI input. An audio selection push button is provided to switch between analog and HDMI audio inputs as desired. The audio selection push button is functional only when the HD‑TXCA‑4KZ‑101 is used with a DM Essentials 4K60 4:4:4 receiver or a DMPS Essentials HD-PS Series switcher.S/PDIF Optical Digital Audio ReturnThe HD‑TXCA‑4KZ‑101 receives S/PDIF optical digital audio from a device (for example, a display) connected to the S/PDIF optical digital audio input of the HD‑RXCA‑4KZ‑101. The S/PDIF optical digital audio output of the HD‑TXCA‑4KZ‑101 then transmits the audio to an AV receiver. Supported S/PDIF digital audio formats are Dolby Digital®, Dolby Digital EX, DTS®, DTS ES, and LPCM up to 6 channels.Compact, Surface‑Mountable DesignCompact in design, the HD‑TXCA‑4KZ‑101 can be mounted onto a flat surface such as the underside of a table, behind a credenza, or inside a podium. It can also be attached to a single rack rail in the back of an equipment cabinet. The HD‑TXCA‑4KZ‑101 can receive power from the included power pack or from the remote DM Essentials receiver or DMPS Essentials switcher.3 Key FeaturesInteroperability with a DM® Essentials receiver or DMPS Essentials switcherPoint-to-point extension of HDMI®, RS-232, IR, and analog audio signals over a CAT5e or higher cableDM Essentials transmission distance up to 130 ft (40 m) for UHD and 4K signals or up to 230 ft (70 m) for 1080p, WUXGA, and 2K signals4K60 4:4:4 capabilityHDR10, HDR10+, and Dolby Vision® video formatsCompliance with HDCP 2.3Analog audio embeddingS/PDIF optical digital audio output for audio return from the HD‑RXCA‑4KZ‑101CEC (Consumer Electronics Control) pass-through capabilityBidirectional RS‑232 and IR pass-through capabilityEDID pass-through capabilityCompact, surface-mountable designPower from 24VDC power pack (included) or from remote DM Essentials receiver or DMPS Essentials switcher

USB over Category Cable Extender, Local and Remote Extends any USB 1.1 or 2.0 device up to 100 meters (330 feet) point-to-point over one CAT5e (or better) unshielded twisted pair cable. Includes the USB‑EXT‑2‑LOCAL and USB‑EXT‑2‑REMOTE USB over Category Cable Extenders. Mounts to a 1-gang electrical box.